Network Topologies

What is network topology?

Network topology refers to the physical or logical arrangement of nodes (such as computers, switches, routers, or other devices) and the connections between them in a computer network.

  • The Blueprint of a Network In simple terms, network topology is like the blueprint or map of a network. It outlines the layout and structure of the network, showing how the devices are interconnected and how data is transmitted between them. It defines the paths that information takes from one node to another and influences the efficiency, scalability, and reliability of the network.
  • Types of Network Topologies There are different types of network topologies, including:
      • Bus
      • Star
      • Ring
      • Mesh
      • Tree
      • Hybrid

    Each topology has its own characteristics, advantages, and limitations, and organizations choose the most suitable one based on their specific requirements and network design goals.

  • The Role of Topology in Network Management By understanding the network topology, network administrators and engineers can plan, manage, and troubleshoot the network effectively. It helps them identify potential bottlenecks, optimize performance, and ensure reliable communication between devices.

Types of network topology

Bus Topology

Bus Topology
Bus Topology Diagram

Pros:

  • Easy installation
  • Fewer cables required than Mesh and star topology
  • Good for small businesses
  • Low cost
  • Easy to manage and expand

Cons:

  • Backbone performance is critical
  • Easily congested on busy periods
  • Efficiency decreases rapidly with each added node
  • Data can only travel in one direction at any point in time

Bus topology is a network type where every device is connected to a single cable that runs from one end of the network to the other. This type of network topology is often referred to as line topology. In a bus topology, data is transmitted in one direction only. If the bus topology has two endpoints then it is referred to as a linear bus topology.

Smaller networks with this type of topology use a coaxial or RJ45 cable to link devices together. However, the bus topology layout is outdated and you’re unlikely to encounter a company using a bus topology today.

Advantages:

  • Simplified layout
  • Cost-effectiveness

Disadvantages:

  • Single point of failure
  • Decreased performance with high traffic
  • Limited suitability
  • Half-duplex limitation

When to use bus topology

Bus topologies were often used in smaller networks. One of the main reasons is that they keep the layout simple. All devices are connected to a single cable so you don’t need to manage a complex topological setup.

The layout also helped make bus topologies cost-effective because they can be run with a single cable. In the event that more devices need to be added then you could simply join your cable to another cable.

When using bus topology is not ideal

However, relying on one cable does mean that bus topologies have a single point of failure. If the cable fails then the entire network will go down. A cable failure would cost organizations a lot of time while they attempt to resume service. Further to this, high network traffic would decrease network performance because all the data travels through one cable.

This limitation makes bus topologies suitable only for smaller networks. The primary reason is that the more network nodes you have, the slower your transmission speeds are going to be. It is also worth noting that bus topologies are limited in the sense that they are half-duplex, which means that data can’t be transmitted in two opposite directions simultaneously.

See also: Network, Server and Application Monitoring for SMBs

Ring Topology

Ring Topology
Ring Topology Diagram

Pros:

  • Low incidence of collision
  • Low cost
  • Suitable for small businesses
  • Dual ring option provides continuity through redundancy

Cons:

  • One faulty node will bring the entire network down
  • Requires extensive preventative maintenance and monitoring
  • Performance declines rapidly with each additional node
  • Reorganizing the network requires a full system shutdown

In networks with ring topology, computers are connected to each other in a circular format. Every device in the network will have two neighbors and no more or no less. Ring topologies were commonly used in the past but you would be hard-pressed to find an enterprise still using them today.

The first node is connected to the last node to link the loop together. As a consequence of being laid out in this format packets need to travel through all network nodes on the way to their destination.

Within this topology, one node is chosen to configure the network and monitor other devices. Ring topologies are half-duplex but can also be made full-duplex. To make ring topologies full-duplex you would need to have two connections between network nodes to form a Dual Ring Topology.

Dual Ring Topology

Dual Ring Topology
Dual Ring Topology Diagram

As mentioned above, if ring topologies are configured to be bidirectional then they are referred to as dual ring topologies. Dual ring topologies provide each node with two connections, one in each direction. Thus, data can flow in a clockwise or counterclockwise direction.

Advantages:

  • Low risk of packet collisions
  • High-speed data transmission
  • Extra protection in dual ring topologies
  • Cost-effectiveness

Disadvantages:

  • High vulnerability: failure of one node or transmission line can disrupt the entire network.
  • Requires constant management
  • Scalability concerns

When to use ring topology

With ring topologies, the risk of packet collisions is very low due to the use of token-based protocols, which only allow one station to transmit data at a given time. This is compounded by the fact that data can move through network nodes at high speeds which can be expanded on when more nodes are added.

Dual ring topologies provided an extra layer of protection because they were more resistant to failures. For instance, if a ring goes down within a node then the other ring can step up and back it up. Ring topologies were also low cost to install.

When using ring topology is not ideal

One of the reasons why ring topologies were replaced is because they are very vulnerable to failure. The failure of one node can take the entire network out of operation. This means that ring topology networks need to be constantly managed to ensure that all network nodes are in good health. However, even if the nodes were in good health your network could still be knocked offline by a transmission line failure!

Ring topologies also raised scalability concerns. For instance, bandwidth is shared by all devices within the network. In addition, the more devices that are added to a network the more communication delay the network experiences. This means that the number of devices added to a network topology needed to be monitored carefully to make sure that the network resources weren’t stretched beyond their limit.

Making changes to a ring topology was also complicated because you need to shut down the network to make changes to existing nodes or add new nodes. This is far from ideal as you’ll need to factor in downtime every time you want to make a change to the topological structure!

See also: Tools To Monitor Throughput

Star Topology

Star Topology
Star Topology Diagram

Pros:

  • Easy to manage from one point – the switch
  • Easy to add and remove nodes
  • Durable
  • Low cable usage
  • Good for small businesses

Cons:

  • Requires specialist network hardware (the switch)
  • Makes the network reliant on the switch’s performance
  • A finite number of switch ports limits the network’s size

A star topology is a topology where every node in the network is connected to one central switch. Every device in the network is directly connected to the switch and indirectly connected to every other node. The relationship between these elements is that the central network hub is a server and other devices are treated as clients. The central node has the responsibility of managing data transmissions across the whole network and acts as a repeater. With star topologies, computers are connected with a coaxial cable, twisted pair, or optical fiber cable.

Advantages:

  • Centralized management
  • Robust against node failure
  • Ease of expansion
  • Simple to setup and manage

Disadvantages:

  • Single point of failure
  • Dependency on central node
  • High setup costs

When to use star topology

Star topologies are most commonly-used because you can manage the entire network from one location: the central switch. As a consequence, if a node that isn’t the central node goes down then the network will remain up. This gives star topologies a layer of protection against failures that aren’t always present with other topology setups. Likewise, you can add new computers without having to take the network offline like you would have to do with a ring topology.

In terms of physical network structure, star topologies require fewer cables than other topology types. This makes them simple to set up and manage over the long-term. The simplicity of the overall network design makes it much easier for administrators to run troubleshooting when dealing with network performance faults.

When using start topology is not ideal

Though star topologies may be relatively safe from failure, if the central switch goes down then the entire network will go down. As such, the administrator needs to manage the health of the central node closely to make sure that it doesn’t go down. The performance of the network is also tied to the central node’s configurations and performance. Star topologies are easy to manage in most ways but they are far from cheap to set up and use.

Tree Topology

Tree Topology
Tree Topology Diagram

Pros:

  • Blends bus and star topologies
  • Easy to manage
  • Easy to expand
  • Suitable for middle-sized businesses

Cons:

  • The network is dependent on the health of the root node
  • Requires networking expertise
  • Involves a lot of cable
  • Larger implementations require monitoring software
  • Can get expensive

As the name suggests, a tree topology network is a structure that is shaped like a tree with its many branches. Tree topologies have a root node that is connected to another node hierarchy. The hierarchy is parent-child where there is only one mutual connection between two connected nodes. As a general rule, a tree topology needs to have three levels to the hierarchy to be classified this way. This form of topology is used within Wide Area Networks to sustain lots of spread-out devices.

Advantages:

  • Extends bus and star topologies
  • Easy troubleshooting

Disadvantages:

  • Vulnerable root node
  • Maintenance complexity
  • Cable intensive

When to use tree topology

The main reason why tree topologies are used is to extend bus and star topologies. Under this hierarchical format, it is easy to add more nodes to the network when your organization grows in size. This format also lends itself well to finding errors and troubleshooting because you can check for network performance issues systematically throughout the tree.

When using tree topology is not ideal

The most significant weakness of tree topology is the root node. If the root node fails then all of its subtrees become partitioned. There will still be partial connectivity within the network amongst other devices such as the failed node’s parent.

Maintaining the network system is not simple either because the more nodes you add, the more difficult it becomes to manage the network. Another disadvantage of a tree topology is the number of cables you need. Cables are required to connect every device throughout the hierarchy which makes the network layout more complex when compared to a simpler topology.

Mesh Topology

Mesh Topology
Mesh Topology Diagram

Pros:

  • High speeds data transfers
  • Durable network that isn’t dependent on any one node
  • Very secure
  • Suitable for high-value networks for small to middle-sized networks
  • Easy to identify faulty equipment

Cons:

  • Requires a very large amount of cable
  • Can be difficult to secrete all the cable
  • Takes a long time to set up
  • Requires meticulous planning
  • There is a limit to the number of cables each computer can accommodate

A mesh topology is a point-to-point connection where nodes are interconnected. In this form of topology, data is transmitted via two methodsrouting and flooding. Routing is where nodes use routing logic to work out the shortest distance to the packet’s destination. In contrast, flooding is where data is sent to all nodes within the network. Flooding doesn’t require any form of routing logic to work.

There are two forms of mesh topologypartial mesh topology and full mesh topology. With partial mesh topology, most nodes are interconnected but there are a few which are only connected to two or three other nodes. A full mesh topology is where every node is interconnected.

Advantages:

  • High reliability
  • No single point of failure
  • High security: Difficult to be compromised due to its setup.

Disadvantages:

  • Complex configuration: Requires significant effort to set up
  • Expensive

When to use mesh topology

Mesh topologies are used first and foremost because they are reliable. The interconnectivity of nodes makes them extremely resistant to failures. There is no single machine failure that could bring down the entire network. The absence of a single point of failure is one of the reasons why this is a popular topology choice. This setup is also secure from being compromised.

When using mesh topology is not ideal

However, mesh topologies are far from perfect. They require an immense amount of configuration once they are deployed. The topological layout is more complex than many other topologies and this is reflected by how long it takes to set up. You’ll need to accommodate a whole host of new wiring which can add up to be quite expensive.

Hybrid Topology

Hybrid Topology
Hybrid Topology Diagram

Pros:

  • Very flexible
  • Suitable for middle-sized and large organizations
  • Infinitely extendible
  • Adaptable to optimize equipment use

Cons:

  • Requires professional management
  • Needs monitoring software
  • Equipment costs are high

When a topology is composed of two or more different topologies it is referred to as a hybrid topology. Hybrid topologies are most-commonly encountered in larger enterprises where individual departments have network topologies that different from another topology in the organization. Connecting these topologies together will result in a hybrid topology. As a consequence, the capabilities and vulnerabilities depend on the types of topology that are tied together.

Advantages:

  • Flexibility
  • High scalability

Disadvantages:

  • Complexity: Each included topology has unique network requirements, making management more difficult.
  • High costs due to its complexity.

When to use hybrid topology

There are many reasons why hybrid topologies are used but they all have one thing in common: flexibility. There are few constraints on the network structure that a hybrid topology cannot accommodate, and you can incorporate multiple topologies into one hybrid setup. As a consequence, hybrid topologies are very scalable. The scalability of hybrid setups makes them well-suited to larger networks.

When using hybrid topology is not ideal

Unfortunately, hybrid topologies can be quite complex, depending on the topologies that you decide to use. Each topology that is part of your hybrid topology will have to be managed according to its unique network requirements. This makes administrators’ jobs more difficult because they are going to have to attempt to manage multiple topologies rather than a single one. In addition, setting up a hybrid topology can end up being quite costly.

See also: Network Discovery Tools and Software

Which topology should I choose?

There is a range of factors that you need to take into account when choosing which topology to use.

Before choosing a topology you’ll want to closely consider the following:

  • Length of cable needed
  • Cable type
  • Cost
  • Scalability

First, you need to take into account the length of the cable you need to provide service to all your network devices. A bus topology is the most lightweight in terms of cable needs. In this sense, this would be the simplest topology to install and buy cables for. This ties into the second factor, you need to consider the type of cable you’re going to use. Cable types range from twister pairs to coaxial cables and optical fiber cables.

The cost of installing the topology is also very important. The more complex the topology you choose is, the more you’ll need to pay in terms of resources and time to create that setup.

The final factor you’ll want to take into account is scalability. If you’re planning to upscale your network infrastructure in the future you want to make sure that you use a network that is easy to add devices to. A star topology network is ideal for this because you can add network nodes with minimal disruption. This isn’t as simple within a ring network because you will incur downtime if you add any nodes.

A look at network topology mapping software

Now that we know the different types of topology, it is time to consider how to design your network from scratch. There are several software products that allow you to create your own network topology diagrams. Network topology diagrams show you a diagram of how your network connects together and helps you to create an efficient network design. It also provides you with a reference point that assists you when you attempt to run troubleshooting to fix faults.

Our methodology for selecting network topology mapping software

We reviewed the market for network topology mapping software and analyzed the options based on the following criteria:

  • Automatic network discovery
  • Live topology map creation for up-to-date
  • Device identifiers and statuses displayed on the map
  • Options for different layout formats
  • Options to manually redesign the network layout within the mapper
  • A free assessment period or money-back guarantee
  • Value for money, represented by a price that represents a good deal for the number of tools the package includes

1. Microsoft Visio

Microsoft Visio Network Diagram Software

There are many different network topology mapping products out there but one of the most widely used is Microsoft Visio.

Pros:

  • Easy to use, part of the Microsoft Suite
  • Good for network planning and theoretical designs
  • Widely used file format
  • Supports a wide range of export types

Cons:

  • Only available in Windows
  • Lacks live network auto-discovery builtin

With Microsoft Visio, you can draw up your network by adding network elements to a canvas. This program allows you to design a topology diagram that details your network. Of course, drawing up your own network isn’t always ideal particularly when you’re attempting to map a larger computer network.

2. Site24x7 Network Monitoring (FREE TRIAL)

site24x7-infra-maps-link-monitors

Site24x7 Network Monitoring includes a network discovery routine that assembles a hardware inventory, listing all switches, routers, and other devices on the network. The package includes a mapping service that generates its maps from the information in the inventory. The discovery process cycles constantly and updates the inventory if any changes have occurred. The map updates automatically. Site24x7 is a cloud platform and you can access it with a 30-day free trial.

Pros:

  • Automatic network discovery
  • Constantly updated network inventory
  • Automatically generated network topology map
  • A full network performance monitoring service

Cons:

  • No on-premises version

Site24x7 Network Monitoring Start a 30-day FREE Trial

3. SolarWinds Network Topology Mapper (FREE TRIAL)

SolarWinds Network Topology Mapper

As a result, you might want to consider using another tool like SolarWinds Network Topology Mapper which can autodiscover devices connected to your network. Autodiscovery comes in handy because it means that you don’t have to draw up your network structure manually.

Pros:

  • Uses auto-discover for automated mapping, great for larger more complex networks
  • Uses multiple protocols to identify network devices, ICMP, SNMP, WMI, and CDP
  • Designed to work in virtual environments and supports both VMWare and Hyper-V hosting
  • Can build static maps and include devices from your network for capacity planning and testing

Cons:

  • Would like to see a longer trial period

SolarWinds Network Topology Mapper Download 14-day FREE Trial

4. Faddom

Faddom Connections Map

Faddom, until recently, called VNT is a mapping system that automatically creates a network topology map through a scanning routine. As well as mapping physical networks, this tool can identify servers and VMs within a hypervisor and map the links between them.

Pros:

  • Scans networks to discover devices
  • Automatically generates a network topology map
  • Creates visual maps of virtualizations
  • Runs as a virtual appliance

Cons:

  • Doesn’t perform network performance monitoring

You can examine this tool with a 30-day free trial.

Choosing Network Topology Mapping & Diagram Software

The network topology you choose for your enterprise should be deeply rooted in your usage requirements. The number of nodes you have in your network will determine whether you can make it by using a bus topology or whether you’re going to need to deploy a more complicated mesh or hybrid setup.

Remember that all topologies have their advantages and disadvantages depending on the environment they’re applied within (even those that have become obsolete!).

Once you’ve given some thought to what topology you want to use you can make the move to deploy it. You can also learn more about Documenting a Network Topology Using CDP.

One good way to plan ahead is to use a network topology mapping tool to draw up the network layout that you’re going to use. Using a tool like SolarWinds Network Topology Mapper will allow you to plot your network on a diagram to view your topological structure in one place.

Network Topology FAQs

What are the types of network topology?

  • Bus Topology Simple layout and cheap but vulnerable to failure and only suitable for low traffic volumes. Not used for office networks today, but can still be found within some consumer products.
  • Ring Topology Easy to manage and with a low risk of collision but reliant on all nodes being powered up and in full working order. Rarely used today.
  • Star Topology All devices are connected to a central switch, which makes it easy to add new nodes without rebooting all currently connected devices. This topology makes efficient use of cable and is easy to administer. On the other hand, the health of the switch is vital. This topology requires monitoring and maintenance. However, it is a commonly encountered topology.
  • Tree Topology A hierarchical layout that links together groups of nodes. Creates parent-child dependencies between root nodes and regular nodes. This layout can be vulnerable to failure if a root node has a problem. This topology is complicated and difficult to manage and it uses a lot of cable.
  • Mesh Topology Each node is connected to every other mode with a direct link. This topology creates a very reliable network, but requires a large amount of cable and is difficult to administer. Wifi networks make this topology more feasible.
  • Hybrid Topology Combines two or more of the standard topologies. This can be a good solution to create quickly link together different existing networks into a unified system. Don’t confuse the term “hybrid network topology” with “hybrid system” – a term that is applied to the combination of onsite and cloud resources.

Related: The Best Network Monitoring Tools